Otherplugs compatible with the Duratec 25 engine include the following: Bosch 96302, NGK 5019 (LTR5GP), If you choose to use a torque wrench, tighten the new spark plugs to about 10-15 ft lbs if you used anti seize or 15-20 ft lbs if they are "dry". I'd recommend just tightening the plugs by hand so that you can feel when the crush washer 30ftlbs of torque at a peak of 1000 less rpm. The Mazda version has forged steel rods, the Ford one doesn’t. Balance shafts. Both the 2.3 and 2.5 have a balance shaft assembly hanging underneath, it’s usually removed when fitting the engine in another car due to its size, weight and it saps some of the power from the engine to drive it. FD245Std con rod bolt: Ford Duratec HE I4 Torque setting 29Nm then +90deg. Ford Duratec HE I4 16v (4 cylinder) Application: Ford EcoSport 2.0 2014- Ford Fiesta Mk6 Fits Engine Type: Ford Duratec HE I4: Product Group: Con Rod Bolts: Stock Status: Stock Lead Time Typically 1-2 weeks: Fits Engine Make: Ford: Catalogue 2023 Page: Installthe main bearing caps in the order indicated in the figure. Tightening torque: (1) 44—46 N·m {4.5—4.6 kgf·m, 32.5—33.9 ft·lbf} (2) 175°—185°. Cylinder Head Bolt Assembly Note. 1. Tighten the cylinder head bolts in the order indicated in the figure in six steps. (1) Tighten to 5.0 N·m {51 kgf·cm, 44.3 in·lbf}. Hereare the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends: Main bearings. Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm. Main bearing bolts: 45 Nm + 90°. Head bolts. Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°. Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Determiningthe correct torque can however present problems. Approximately 90% of the applied torque is employed in overcoming friction, 50% at the bearing face of the nut and 40% between the mating threads. It can therefore be seen that only something in the order of 10% effort is employed inducing axial load in the bolt. x8JETA. Whatis the torque of the Ford Focus. 2019 Focus IV Active Hatchback | 2019 - to present. Modification. Torque. Rotations per minute. 2.0 EcoBlue Automatic / 150 hp (112 kW) 370 Nm. 273 lb-ft. -. Theymust be replaced when the head is re-installed. thanks for the reply, it's for an 02 Escape v6. Stage 1: Tighten to 40 Nm (30 lb-ft). Stage 2: Tighten bolts 90 degrees. Stage 3: Loosen one full turn. Stage 4: Tighten to 40 Nm (30 lb-ft). Stage 5: Tighten 90 degrees. Stage 6: Tighten 90 degrees. Iwill be needing a new engine for my new mk2 escort circuit car soon and i am having a hard time deciding on which engine to go for. Duratec-PRO's Proven 290-300 BHP Reliable The 2.0ltr revs to over 9K rpm Light weight, alloy block etc CONS Quite pricey Expensive conversion parts Looks shit Doesn't suit an old skool racer N/A YB - PRO's The2014-2018 Ford Focus is the facelifted Mk3 model and comes with 1.0 litre Ecoboost as well as 1.6-litre petrol engines. Diesel options initially included a new 1.5-litre diesel engine and 1.6 diesel unit, which was carried over from the pre-facelifted car. Maxtorque. 203 Nm @ 6300 rpm. Weight. 560kg (specification dependent) 0-60 mph Bilstein race suspension with fully-adjustable dampers with ten stiffness settings. STANDARD EQUIPMENT . Chassis & Exterior . Standard size chassis with dedion rear 2.0 Litre Ford Duratec Engine. 130 MPH. 180 BHP. From £38,490. DIscover Seven 420 Ifyou or a customer use aftermarket performance bolts such as the ARP bolts that are sold on our website, follow the recommended torque specifications. 260 - 289 - 302 Torque Spec. 60-70 ft/lbs. Outer Main Cap Bolts. 35-40 ft/lbs. Connecting Rod Bolts (. 30-35 ft/lbs. Connecting Rod Bolts ( 289 & 302. 40-45 ft/lbs.

2.0 duratec engine torque settings